彩票365下载

產品

  • 煤礦井下用聚乙烯管道系統

    壓力等級:煤礦井下用供水排水、壓風、噴漿管材公稱壓力為0.4MPa~1.6 MPa
    抽放瓦斯氣體管材的最高公稱壓力為-0.097MPa。
    規格型號:dn20mm~dn1200mm

  • 聚乙烯燃氣管道

    規格型號:dn20mm~dn630mm。



  • 給水用聚乙烯管道系統

    壓力等級:0.4MPa~1.6MPa。
    規格型號:dn20mm~dn1200mm。


  • 電熔異徑直接

    規格型號:dn 50mm~dn 315mm

  • PE燃氣用冷凝水缸

    壓力等級:燃氣輸配工作壓力不大于0.5MPa
    Pressure grade: the gas distribution working pressure is not larger than 0.5MPa
    規格型號:dn 63mm~dn 315mm
    Specification and model: dn 63mm~dn 315mm

  • PE注塑管帽

    壓力等級:輸水工作壓力dn<400mm PE注塑管帽最大公稱壓力1.25MPa, dn≥400mm PE注塑管帽最大公稱壓力1.0MPa;燃氣輸配壓力可達0.4mpa
    Pressure grade: for water conveying working pressure, when dn<400mm, the maximum nominal pressure of PE plastic injection pipe cap is 1.25MPa; when dn≥400mm, the maximum nominal pressure of PE plastic injection pipe cap is 1.0MPa; the gas distribution pressure can reach 0.4mpa.
    規格型號:dn 25mm~dn 630mm
    Specification and model: dn 25mm~dn 630mm

  • PE焊制四通

    壓力等級:適用于工作壓力不大于1.25MPa
    Pressure grade: suitable for the working pressure not larger than 1.25MPa
    規格型號:dn 90mm~dn 1000mm
    Specification and model: dn 90mm~dn 1000mm

  • PE 注塑四通

    壓力等級:適用于工作壓力不大于1.6MPa
    Pressure grade: suitable for the working pressure not larger than 1.6MPa

    規格型號:dn 63mm~dn 355mm
    Specification and model: dn 63mm~dn 355mm

  • PE 90°彎頭

    90°注塑彎頭 壓力等級:dn<400mm PE 90°注塑彎頭最大公稱壓力1.6MPa,dn≥400mm,PE 90°注塑彎頭最大公稱壓力1.0MPa
    Pressure grade: for PE 90° plastic injection elbow with dn<400mm, the maximum nominal pressure is 1.6MPa. For PE 90° plastic injection elbow with dn≥400mm, the maximum nominal pressure is 1.0MPa.
    規格型號:dn 90mm~dn 630mm
    Specification and model: dn 90mm~dn 630mm
    90°焊制彎頭 壓力等級:適用于工作壓力不大于1.25MPa
    Pressure grade: suitable for the working pressure not larger than 1.25MPa
    規格型號:dn 250mm~dn 1200mm
    Specification and model: dn 250mm~dn 1200mm

           

加載更多
  • 彩票365下载